Why Understanding Essential Plumbing Skills is Important For Installing a Bathtub
Why Understanding Essential Plumbing Skills is Important For Installing a Bathtub
Blog Article
Were you trying to locate info about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround?
Setting up a tub isn't specifically rocket science, however it does require strong plumbing, carpentry, and often, tiling skills. Changing an old bath tub with a new one is likewise a moderately tough job. If the old tub is readily easily accessible, the task can move immediately; if you need to open up a wall surface to eliminate the old tub as well as place the new bath tub, the task is much harder. In either case, the job is within a residence handyman's skills, although you will need a helper to move out the old bathtub and also embeded in the new one. Ensure you have certified on your own for the task and fit attempting it. Rather than working with a service provider to take control of a halfway-completed project, it is far better to consider employing one prior to you begin. Possibilities are you might need a professional plumber to make tube links.
This post will aid you mount a brand-new tub in your washroom if you have actually already acquired a new tub as well as don't require to alter the plan of your previous water system pipes.
Your devices and material checklist ought to make up the following:
Getting ready for the Setup
Firstly, the sustaining framework supplied with the bath must be fitted (if needed) according to the maker's directions. Next, fit the faucets or mixer to the bathtub. When fitting the tap block, it is very important to make certain that if the tap includes a plastic washer, it is fitted between the bathroom and also the faucets. On a plastic bath, it is additionally practical to fit a supporting plate under the taps device to prevent pressure on the tub.
Fit the adaptable tap ports to the bottom of the two taps making use of 2 nuts and also olives (occasionally supplied with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet hole, and then pass the electrical outlet via the hole in the bath. Use the nut provided by the producer to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipe.
Next, fit the end of the versatile overflow pipeline to the overflow electrical outlet. Afterwards, screw the pipeline to the overflow face which must be fitted inside the bathroom. See to it you make use of every one of the supplied washers.
Connect the trap to the bottom of the waste electrical outlet on the tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the trap to the electrical outlet. Connect all-time low of the overflow tube in a similar manner.The bath need to now be ready to be suited its last placement.
Removing Old Touches
If you require to change old faucets with brand-new ones as a part of your installation, after that the first thing you must do is disconnect the supply of water. After doing so, turn on the taps to drain any type of water staying in the system. The process of removing the existing faucets can be fairly bothersome because of the restricted gain access to that is commonly the case.
Utilize a container wrench (crowsfoot spanner) or a faucet tool to undo the nut that attaches the supply pipes to the taps. Have a cloth prepared for the staying water that will come from the pipes. When the supply pipelines have actually been removed, use the exact same device to loosen up the nut that holds the faucets onto the bath/basin. You will certainly require to quit the solitary taps from transforming throughout this process. Once the faucets have been removed, the holes in the bath/basin will certainly have to be cleaned of any kind of old sealing substance.
Before proceeding to fit the brand-new faucets, compare the pipeline connections on the old taps to the brand-new faucets. If the old taps are longer than the brand-new faucets, then a shank adapter is required for the brand-new taps to fit.
Setting up the Tub
Utilizing the two wooden boards under its feet, put the tub in the called for position. The wood boards are useful in uniformly spreading the weight of the tub over the location of the boards instead of focusing all the weight onto 4 tiny points.
The next goal is to make certain that the bathtub is leveled all round. This can be attained by checking the level and changing the feet on the bathtub up until the level reviews degree.
To mount faucets, fit all-time low of the outermost flexible tap connector to the suitable supply pipe by making a compression join; then do the same for the various other faucet.
Turn on the water as well as inspect all joints and new pipework for leakages and tighten them if required. Load the tub as well as also check the overflow electrical outlet and also the typical electrical outlet for leakages.
Ultimately, repair the bath paneling as described in the supplier's instruction manual. Tiling and securing around the bath tub should wait until the bathtub has been used at least when as this will resolve it right into its final position.
Fitting New Taps
If the tails of the brand-new faucets are plastic, after that you will certainly require a plastic port to stop damages to the string. One end of the port fits on the plastic tail of the faucet as well as the other end offers a connection to the existent supply pipes.
If you require to fit a monobloc, after that you will require decreasing couplers, which connects the 10mm pipeline of the monobloc to the standard 15mm supply pipeline.
Next off, position the faucet in the installing hole in the bath/basin guaranteeing that the washers remain in location between the faucet and also the sink. Safeguard the tap in position with the maker offered backnut. As soon as the tap is firmly in place, the supply pipelines can be connected to the tails of the taps. The faucets can either be connected by utilizing corrugated copper piping or with regular tap ports. The previous type must be attached to the tap ends first, tightening up only by hand. The supply pipes can later on be attached to the various other end. Tighten both ends with a spanner after both ends have been linked.
Tiling Around the Tub
In the location where the bathroom fulfills the floor tile, it is necessary to seal the joins with a silicone rubber caulking. This is essential as the fitting can move enough to crack a rigid seal, causing the water to penetrate the wall surface in between the bath and the tiling, resulting in problems with dampness and also feasible leaks to the ceiling listed below.
You can select from a variety of coloured sealers to assimilate your fixtures and also fittings. They are marketed in tubes as well as cartridges, and are capable of securing gaps as much as a width of 3mm (1/8 inch). If you have a bigger gap to fill, you can load it with twists of soaked paper or soft rope. Remember to always load the tub with water prior to securing, to allow for the motion experienced when the tub is in use. The sealer can fracture relatively very early if you do not take into consideration this activity before securing.
Conversely, ceramic coving or quadrant ceramic tiles can be used to edge the bath or shower tray. Plastic strips of coving, which are easy to use and also cut to size, are additionally quickly readily available on the marketplace. It is recommended to fit the ceramic tiles making use of waterproof or waterproof sticky and grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
We were made aware of that article on Installing A Bathtub through a friend on our other web address. Be sure to take the time to promote this blog post if you appreciated it. We recognize the value of reading our article about How to Install a Bathtub Yourself.
Avoid further plumbing damage; call. Report this page